- #BLUESUITE SOFTWARE SOFTWARE#
- #BLUESUITE SOFTWARE BLUETOOTH#
- #BLUESUITE SOFTWARE WINDOWS#
This release has been tested on the following versions of the Windows Operating System.
When using voice assistants, noise is heard, perhaps noise canceling is not possible.There aren’t important updates and improvements for this release. (Low-frequency mode does not turn on after reboot) By default, the column is turned on with the last mode selected. This is normal, as there is water left in the speakers or the emitters themselves, you must wait until it dries, or push it out with a sound. Dipped in water \ got water and the column began to wheeze. For those who disassembled the column, if they removed only the fabric, mesh, grill, then nothing will happen. There is indeed protection against water, but it is better not to dip the device once again under water. Many wrote about this, but I repeat, only a Connect + column can connect to Flip 4. Many complain about the charge indicator, in order to check it, just click on any of the buttons, for example, decrease the volume. #BLUESUITE SOFTWARE SOFTWARE#
The column will announce the software version.
You can find out what the firmware is with the volume down and connect + buttons. (Turned on by normal BT mode switching + Volume down button) In some columns there are really 3 modes, as in my Flip 4 SE 3.2.0. The column can be placed on its side, for this special irregularities are provided for the removal of pressure. It doesn’t matter what mode you have, just don’t set the maximum volume, and then it will live longer both in terms of battery and in terms of wear of the speakers themselves. The phonite column is normal for this segment. 
Passive radiators will not "fly out" with strong fluctuations. Therefore, you can connect at the moment by updating the firmware of JBL Charge 3. Can I connect to JBL FLIP4 ( JBL Charge 3, JBL FLIP3 ) - There is JBL connect on Flip 4 +, on Flip 3 JBL connect. the inclusion of a service mode, the so-called "bass mode", is not recommended The mode leads to the failure of the column outside the service center, and the user does its inclusion at his own risk! The low-frequency mode "Bluetooth" + "Loud-" 10 sec (more bass and more vibrating radiators) It turns off as well. #BLUESUITE SOFTWARE BLUETOOTH#
Hard reset "Volume +" + "Play" 3 sec (useful when you need to clear the bluetooth steam table).Passive radiators DO NOT TOUCH! They can very easily fail.Play / Pause (two times) - the next track.Play / Pause + Volume + (hold 2 sec.) - knocks the column to the factory settings.Thanks to for these four combinations.Play / Pause + Volume- + Volume + - cold reset of the processor at the iron level (simulates a power outage from the processor), exit from DFU.To exit mode disconnect USB, hold Play / Pause + Volume- + Volume + for a few seconds (there will be no visual reaction), wait a few seconds and just turn on the column. Play / Pause + Volume- (hold 10 sec.) (Danger! There is an opportunity to absolutely brick a column! Do not press buttons in programs unless you know what they are doing!) - enable the normal DFU firmware mode, the column is detected via USB and there is some functionality in the CSR BlueSuite software package (flashing, editing memory, console).
Bluetooth + Volume + (hold 10 sec.) - enable DFU HID firmware mode, the column is detected via USB as a HID input device.To disable the mode, connect the speaker to charging, after the sound of switching on, hold down the same combination. JBL Connect + Volume + (hold 10 sec.) - demo mode, the speaker works only from the network and the sound goes only through the cable.May void the warranty and damage the sound. At low volume, bass will be less, and at high volume there will be overload (strong distortion of sound). Bluetooth + Volume - (hold 10 sec.) ( Dangerously! ) - disables the built-in equalizer, compressor, etc.JBL Connect + Volume - (hold 2 sec.) - the column says the firmware version (you need to enable sounds on Connect +) and blinks charge indicators for the firmware version.
0 kommentar(er)
